Chapter 4: IDS Panels

• IDS805 Programming
• IDS806 Programming
• IDS816 Programming
• IDS X64 Programming

IDS805 Programming

IDS805 panels with grey serial cable on external serial connector

---

Basic Programming

Locations 43 to 46

• Enter [Account code]

Location 47

• Enter 6 (Contact ID)

Locations 48 to 54

• Enter 5555555

Location 151

• Default is 4 dial attempts
• Enter 0 to disable the dialer

---

Important Notes

• Tone and force dialling are enabled by default
• LTE GSM must be powered directly from battery
• Do not power from panel auxiliary output

---

App Configuration

For mobile app connectivity:

Requirements:

• App version v4.37 or latest vE4.xx
• Serial Port must be set to Orisec/IDS805
• Requires a VALID user code

---

Troubleshooting

• If no communication, verify power is from battery
• Test with known working user code

IDS806 Programming

IDS806 panels with red serial cable

---

Basic Programming

Locations 43 to 46

• Enter [Account code]

Location 47

• Enter 6 (Contact ID)

Locations 48 to 54

• Enter 5555555

Location 196

• Must be 000000
• Critical for proper operation

---

Installation Procedure

Important: Follow this exact sequence:

1. Ensure panel power is OFF
2. Connect serial port only (no panel power)
3. Power up the panel
4. Serial port will be automatically detected

---

Tested Versions

Successfully tested on firmware versions:

• 1.12
• 1.13
• 1.14
• 1.15
• 1.88

---

Critical Notes

• Location 196 must be all zeros
• Panel reboot required after serial connection
• Red serial cable indicates IDS806 compatibility

IDS816 Programming

IDS816 panel programming locations

---

Basic Programming

Location 111

• LED 1 ON
• All other LEDs OFF

Location 116

• Enter 5 for Contact ID

Location 121

• Enter 5555555

Location 128 Sub 2

• Enter [Account code]

---

Programming Tips

• Ensure only LED 1 is on in location 111
• Double-check sublocation 2 for account code
• Test communication after programming

IDS X64 Programming

Complete guide for all X64 variants

---

Basic Programming (All Versions)

Location 41

• Default setting usually fine
• Set to 5 for Contact ID on Telephone Number 1

Location 46

• Subloc 1 (LED 1): ON for Tone dialling
• Subloc 2 (LED 2): OFF
• Subloc 3 (LED 3): OFF

Location 47

• Set to 6

Location 51

• Enter 5555555 (seven 5's)

Location 61-68 (Account Codes)

• Loc 61: Partition 1 account code (4 digits)
• Loc 62: Partition 2 account code
• Loc 63-68: Partitions 3-8 account codes

Location 71 (72 = P2 -> 78 = P8)

• Serial account code (same as partition account code)

Location 196

• Must be 000000

Location 501-564

• Option 3 must be set to Yes

Enable User Code Bypassing Hold [ * ] → beep → [MASTER CODE] [ * ] [ 1 ] [ 0 ] [ * ] [USER CODE] [ * ] [BITMAP] [ * ] [ # ]

Bitmap(Option 8) Zone Bypass Enable MUST be set to Yes

---

Open/Close Reporting by User

For X64 Older than 2017

Programming Sequence: Hold [ * ] → beep → [ MASTER CODE ] [ * ] [ 1 ] [ 4 ] [ * ] [ USER CODE ] [ * ] [ BITMAP ] [ * ] [ # ]

Enable User Reporting Codes:

Subloc/LED	Default	Action
1	OFF	Set ON to enable close reporting
2	OFF	Set ON to enable stay close reporting
3	OFF	Set ON to enable open reporting
4	OFF	Set ON to enable siren cancel reporting

Important: Must be repeated for EACH user requiring open/close reporting!

For X64 New (2017 onwards)

1. Enter Installer Mode
2. Go to Partition Arm Options (Locations 211-218)
3. Enable option 16 (Open/Closing User Reporting), this option is global for all users in the partition.

---

Arm Without User Code Reporting

For quick-arm and key-switch arming:

Locations 581-588 (Split Reporting Data)

• Subloc 7: Set ON to enable "Armed without user code" reporting
• Location 581 for Partition 1
• Location 582 for Partition 2
• Locations 583-588 for Partitions 3-8

---

Serial/App Programming

Requirements:

• Panel firmware: V2.80 or above
• GSM firmware: V4.51 or above OR E4.19
• Draw power from Aux 12V, NOT from serial cable

Programming:

• Loc 40: Ensure value 5 (CID) is programmed
• Loc 61: Account code required
• Loc 196: Must be 000000

24V Version Additional:

• Loc 71: Account code required

---

Troubleshooting

• If you can connect but get Bypassed zones and are unable to do anything: Check Loc 196 = 000000
• After changing Loc 196: Remove panel from app and re-add
• Cannot control panel: Verify user code
• Connection issues: Check power source (must be Aux 12V)