Chapter 4: IDS Panels

IDS805 Programming
IDS805 panels with grey serial cable on external serial connector 
 
 Basic Programming 
 Locations 43 to 46 
 
 Enter [Account code] 
 
 Location 47 
 
 Enter 6 (Contact ID) 
 
 Locations 48 to 54 
 
 Enter 5555555 
 
 Location 151 
 
 Default is 4 dial attempts 
 Enter 0 to disable the dialer 
 
 
 Important Notes 
 
 Tone and force dialling are enabled by default 
 LTE GSM must be powered directly from battery 
 Do not power from panel auxiliary output 
 
 
 App Configuration 
 For mobile app connectivity: 
 Requirements: 
 
 App version v4.37 or latest vE4.xx 
 Serial Port must be set to Orisec/IDS805 
 Requires a VALID user code 
 
 
 Troubleshooting 
 
 If no communication, verify power is from battery 
 Test with known working user code

IDS806 Programming
IDS806 panels with red serial cable 
 
 Basic Programming 
 Locations 43 to 46 
 
 Enter [Account code] 
 
 Location 47 
 
 Enter 6 (Contact ID) 
 
 Locations 48 to 54 
 
 Enter 5555555 
 
 Location 196 
 
 Must be 000000 
 Critical for proper operation 
 
 
 Installation Procedure 
 Important: Follow this exact sequence: 
 
 Ensure panel power is OFF 
 Connect serial port only (no panel power) 
 Power up the panel 
 Serial port will be automatically detected 
 
 
 Tested Versions 
 Successfully tested on firmware versions: 
 
 1.12 
 1.13 
 1.14 
 1.15 
 1.88 
 
 
 Critical Notes 
 
 Location 196 must be all zeros 
 Panel reboot required after serial connection 
 Red serial cable indicates IDS806 compatibility

IDS816 Programming
IDS816 panel programming locations 
 
 Basic Programming 
 Location 111 
 
 LED 1 ON 
 All other LEDs OFF 
 
 Location 116 
 
 Enter 5 for Contact ID 
 
 Location 121 
 
 Enter 5555555 
 
 Location 128 Sub 2 
 
 Enter [Account code] 
 
 
 Programming Tips 
 
 Ensure only LED 1 is on in location 111 
 Double-check sublocation 2 for account code 
 Test communication after programming

IDS X64 Programming
Complete guide for all X64 variants 
 
 Basic Programming (All Versions) 
 Location 41 
 
 Default setting usually fine 
 Set to 5 for Contact ID on Telephone Number 1 
 
 Location 46 
 
 Subloc 1 (LED 1): ON for Tone dialling 
 Subloc 2 (LED 2): OFF 
 Subloc 3 (LED 3): OFF 
 
 Location 47 
 
 Set to 6 
 
 Location 51 
 
 Enter 5555555 (seven 5's) 
 
 Location 61-68 (Account Codes) 
 
 Loc 61: Partition 1 account code (4 digits) 
 Loc 62: Partition 2 account code 
 Loc 63-68: Partitions 3-8 account codes 
 
 Location 71 (72 = P2 -> 78 = P8) 
 
 Serial account code (same as partition account code) 
 
 Location 196 
 
 Must be 000000 
 
 Location 501-564 
 
 Option 3 must be set to Yes 
 
 Enable User Code Bypassing 
Hold [ * ] → beep → [MASTER CODE] [ * ] [ 1 ] [ 0 ] [ * ] [USER CODE] [ * ] [BITMAP] [ * ] [ # ] 
 Bitmap(Option 8) Zone Bypass Enable
MUST be set to Yes 
 
 Open/Close Reporting by User 
 For X64 Older than 2017 
 Programming Sequence: 
Hold [ * ] → beep → [ MASTER CODE ] [ * ] [ 1 ] [ 4 ] [ * ] [ USER CODE ] [ * ] [ BITMAP ] [ * ] [ # ] 
 Enable User Reporting Codes: 
 
 
 
 Subloc/LED 
 Default 
 Action 
 
 
 
 
 1 
 OFF 
 Set ON to enable close reporting 
 
 
 2 
 OFF 
 Set ON to enable stay close reporting 
 
 
 3 
 OFF 
 Set ON to enable open reporting 
 
 
 4 
 OFF 
 Set ON to enable siren cancel reporting 
 
 
 
 Important: Must be repeated for EACH user requiring open/close reporting! 
 For X64 New (2017 onwards) 
 
 Enter Installer Mode 
 Go to Partition Arm Options (Locations 211-218) 
 Enable option 16 (Open/Closing User Reporting), this option is global for all users in the partition. 
 
 
 Arm Without User Code Reporting 
 For quick-arm and key-switch arming: 
 Locations 581-588 (Split Reporting Data) 
 
 Subloc 7: Set ON to enable "Armed without user code" reporting 
 Location 581 for Partition 1 
 Location 582 for Partition 2 
 Locations 583-588 for Partitions 3-8 
 
 
 Serial/App Programming 
 Requirements: 
 
 Panel firmware: V2.80 or above 
 GSM firmware: V4.51 or above OR E4.19 
 Draw power from Aux 12V, NOT from serial cable 
 
 Programming: 
 
 Loc 40: Ensure value 5 (CID) is programmed 
 Loc 61: Account code required 
 Loc 196: Must be 000000 
 
 24V Version Additional: 
 
 Loc 71: Account code required 
 
 
 Troubleshooting 
 
 If you can connect but get Bypassed zones and are unable to do anything: Check Loc 196 = 000000 
 After changing Loc 196: Remove panel from app and re-add 
 Cannot control panel: Verify user code 
 Connection issues: Check power source (must be Aux 12V)