IDS X64 Programming

Complete guide for all X64 variants 
 
 Basic Programming (All Versions) 
 Location 41 
 
 Default setting usually fine 
 Set to 5 for Contact ID on Telephone Number 1 
 
 Location 46 
 
 Subloc 1 (LED 1): ON for Tone dialling 
 Subloc 2 (LED 2): OFF 
 Subloc 3 (LED 3): OFF 
 
 Location 47 
 
 Set to 6 
 
 Location 51 
 
 Enter 5555555 (seven 5's) 
 
 Location 61-68 (Account Codes) 
 
 Loc 61: Partition 1 account code (4 digits) 
 Loc 62: Partition 2 account code 
 Loc 63-68: Partitions 3-8 account codes 
 
 Location 71 (72 = P2 -> 78 = P8) 
 
 Serial account code (same as partition account code) 
 
 Location 196 
 
 Must be 000000 
 
 Location 501-564 
 
 Option 3 must be set to Yes 
 
 Enable User Code Bypassing 
Hold [ * ] → beep → [MASTER CODE] [ * ] [ 1 ] [ 0 ] [ * ] [USER CODE] [ * ] [BITMAP] [ * ] [ # ] 
 Bitmap(Option 8) Zone Bypass Enable
MUST be set to Yes 
 
 Open/Close Reporting by User 
 For X64 Older than 2017 
 Programming Sequence: 
Hold [ * ] → beep → [ MASTER CODE ] [ * ] [ 1 ] [ 4 ] [ * ] [ USER CODE ] [ * ] [ BITMAP ] [ * ] [ # ] 
 Enable User Reporting Codes: 
 
 
 
 Subloc/LED 
 Default 
 Action 
 
 
 
 
 1 
 OFF 
 Set ON to enable close reporting 
 
 
 2 
 OFF 
 Set ON to enable stay close reporting 
 
 
 3 
 OFF 
 Set ON to enable open reporting 
 
 
 4 
 OFF 
 Set ON to enable siren cancel reporting 
 
 
 
 Important: Must be repeated for EACH user requiring open/close reporting! 
 For X64 New (2017 onwards) 
 
 Enter Installer Mode 
 Go to Partition Arm Options (Locations 211-218) 
 Enable option 16 (Open/Closing User Reporting), this option is global for all users in the partition. 
 
 
 Arm Without User Code Reporting 
 For quick-arm and key-switch arming: 
 Locations 581-588 (Split Reporting Data) 
 
 Subloc 7: Set ON to enable "Armed without user code" reporting 
 Location 581 for Partition 1 
 Location 582 for Partition 2 
 Locations 583-588 for Partitions 3-8 
 
 
 Serial/App Programming 
 Requirements: 
 
 Panel firmware: V2.80 or above 
 GSM firmware: V4.51 or above OR E4.19 
 Draw power from Aux 12V, NOT from serial cable 
 
 Programming: 
 
 Loc 40: Ensure value 5 (CID) is programmed 
 Loc 61: Account code required 
 Loc 196: Must be 000000 
 
 24V Version Additional: 
 
 Loc 71: Account code required 
 
 
 Troubleshooting 
 
 If you can connect but get Bypassed zones and are unable to do anything: Check Loc 196 = 000000 
 After changing Loc 196: Remove panel from app and re-add 
 Cannot control panel: Verify user code 
 Connection issues: Check power source (must be Aux 12V)