# miPanic Panel # New Page # miPanic Quick Reference Guide The **miPanic** is a versatile security system featuring 4 supervised zones and support for up to 64 user codes or remotes via a built-in receiver. --- ## 1. System Overview - **Zones:** 4 Supervised zones (Requires $3.3k\\Omega$ End-of-Line resistors). - **Capacity:** 64 User codes and/or remotes. - **PGM Output (ARM LED Mode):** - **Solid:** System Armed. - **Off:** System Disarmed. - **Flashing:** Alarm has been triggered. - **Flickering:** Force armed (armed while a zone was open). - **Zone Logic:** If armed with an open zone, that zone is ignored until it closes, then it becomes active. --- ## 2. Programming: No Keypad (Jumper Method) To program using the jumpers on the board: 1. Set the jumpers to the desired configuration (see table below). 2. Hold the **Reset** button down. 3. Connect power to the board. 4. Release the **Reset** button once **LED 1** flashes briefly. ### Configuration Modes

Setup Type	Zone Logic
Panic Setup	All zones function as Panic zones.
Mini Alarm	Zones 1-3: Burglary; Zone 4: Panic.
Mini Alarm (Delay)	Zone 1: Entry/Exit Delay; Zones 2-3: Burglary; Zone 4: Keyswitch.

### Remote Management (Jumper Method) - **Add Remotes:** Set jumpers to "Add" position $\\rightarrow$ Hold Reset until LED 1 flashes $\\rightarrow$ Press any remote button (Siren will toot). - **Delete All Remotes:** Set jumpers to "Delete All" position $\\rightarrow$ Hold Reset until LED 1 flashes. - **Delete Individual Remote:** Set jumpers to "Delete Individual" position $\\rightarrow$ Hold Reset until LED 1 flashes $\\rightarrow$ Press a button on the specific remote to remove it. --- ## 3. Programming: With Keypad ### Installer Mode Access by entering: `[Installer Code] (Default 9999)` + `*`

Location	Description	Details
0	Default Options	0=All, 1=Master Code (1234), 2=Users, 3=Download Code, 4=WiFi, 5=Wireless Sensors.
1	Panel Setup	1=Panic, 2=Mini Alarm, 3=Mini Alarm with Delay.
2	Account Code	Enter 4-digit code for reporting.
3	Installer Code	Enter new 4-digit installer code.
4	Enroll Wireless	(Firmware E3.04 and up).

### User Code Programming Access by entering: `Alt` + `*` + `[Master Code] (Default 1234)` + `*`

Loc	Action	Instruction
1	Add User	Enter 4-digit code + `*`. Press remote button to link, or `#` to skip.
2	Change User	Enter existing code + `*`. Enter new code or press remote button.
3	Delete User	Enter 4-digit code + `*` to remove both code and remote.
4	Delete by ID	Enter User Number (e.g., 1 for Master) + `*`.
5	Add Remote Only	Press remote button to enroll. Repeat for more, press `#` to exit.

--- ## 4. User Operations ### Bypassing Zones 1. Press `Alt` + `9`. 2. Press the **Zone Number** followed by `*` to toggle bypass. 3. Press `#` to exit. - *Note: Panic and Keyswitch zones cannot be bypassed.* ### Trouble Conditions If the **Power LED** is flashing **Red**, press `Alt` + `7`. The Zone LEDs will indicate the specific issue:

LED	Description	LED	Description
1	Siren Tamper	5	Comms Fail
2	Aux 12V Fuse	6	Low Battery
3	Box Tamper	7	Network Problem
4	AC Fail

---

Location	Description	Details
0	Default Options	0=All, 1=Master Code (1234), 2=Users, 3=Download Code, 4=WiFi, 5=Wireless Sensors.
1	Panel Setup	1=Panic, 2=Mini Alarm, 3=Mini Alarm with Delay.
2	Account Code	Enter 4-digit code for reporting.
3	Installer Code	Enter new 4-digit installer code.
4	Enroll Wireless	(Firmware E3.04 and up).

Loc	Action	Instruction
1	Add User	Enter 4-digit code + `*`. Press remote button to link, or `#` to skip.
2	Change User	Enter existing code + `*`. Enter new code or press remote button.
3	Delete User	Enter 4-digit code + `*` to remove both code and remote.
4	Delete by ID	Enter User Number (e.g., 1 for Master) + `*`.
5	Add Remote Only	Press remote button to enroll. Repeat for more, press `#` to exit.