New Page
miPanic Quick Reference Guide
The miPanic is a versatile security system featuring 4 supervised zones and support for up to 64 user codes or remotes via a built-in receiver.
1. System Overview
- Zones: 4 Supervised zones (Requires $3.3k\Omega$ End-of-Line resistors).
- Capacity: 64 User codes and/or remotes.
- PGM Output (ARM LED Mode):
- Solid: System Armed.
- Off: System Disarmed.
- Flashing: Alarm has been triggered.
- Flickering: Force armed (armed while a zone was open).
- Zone Logic: If armed with an open zone, that zone is ignored until it closes, then it becomes active.
2. Programming: No Keypad (Jumper Method)
To program using the jumpers on the board:
- Set the jumpers to the desired configuration (see table below).
- Hold the Reset button down.
- Connect power to the board.
- Release the Reset button once LED 1 flashes briefly.
Configuration Modes
| Setup Type | Zone Logic |
|---|---|
| Panic Setup | All zones function as Panic zones. |
| Mini Alarm | Zones 1-3: Burglary; Zone 4: Panic. |
| Mini Alarm (Delay) | Zone 1: Entry/Exit Delay; Zones 2-3: Burglary; Zone 4: Keyswitch. |
Remote Management (Jumper Method)
- Add Remotes: Set jumpers to "Add" position $\rightarrow$ Hold Reset until LED 1 flashes $\rightarrow$ Press any remote button (Siren will toot).
- Delete All Remotes: Set jumpers to "Delete All" position $\rightarrow$ Hold Reset until LED 1 flashes.
- Delete Individual Remote: Set jumpers to "Delete Individual" position $\rightarrow$ Hold Reset until LED 1 flashes $\rightarrow$ Press a button on the specific remote to remove it.
3. Programming: With Keypad
Installer Mode
Access by entering: [Installer Code] (Default 9999) + *
| Location | Description | Details |
|---|---|---|
| 0 | Default Options | 0=All, 1=Master Code (1234), 2=Users, 3=Download Code, 4=WiFi, 5=Wireless Sensors. |
| 1 | Panel Setup | 1=Panic, 2=Mini Alarm, 3=Mini Alarm with Delay. |
| 2 | Account Code | Enter 4-digit code for reporting. |
| 3 | Installer Code | Enter new 4-digit installer code. |
| 4 | Enroll Wireless | (Firmware E3.04 and up). |
User Code Programming
Access by entering: Alt + * + [Master Code] (Default 1234) + *
| Loc | Action | Instruction |
|---|---|---|
| 1 | Add User | Enter 4-digit code + *. Press remote button to link, or # to skip. |
| 2 | Change User | Enter existing code + *. Enter new code or press remote button. |
| 3 | Delete User | Enter 4-digit code + * to remove both code and remote. |
| 4 | Delete by ID | Enter User Number (e.g., 1 for Master) + *. |
| 5 | Add Remote Only | Press remote button to enroll. Repeat for more, press # to exit. |
4. User Operations
Bypassing Zones
- Press
Alt+9. - Press the Zone Number followed by
*to toggle bypass. - Press
#to exit.- Note: Panic and Keyswitch zones cannot be bypassed.
Trouble Conditions
If the Power LED is flashing Red, press Alt + 7. The Zone LEDs will indicate the specific issue:
| LED | Description | LED | Description |
|---|---|---|---|
| 1 | Siren Tamper | 5 | Comms Fail |
| 2 | Aux 12V Fuse | 6 | Low Battery |
| 3 | Box Tamper | 7 | Network Problem |
| 4 | AC Fail |