Search Results

This guide provides step-by-step instructions for using the Finmon Asset Management Portal. It is intended for existing and new Finmon clients. SIM_Management_Portal_User_Guide.html

html version of mi63 Installer Manual mi64-Installer-Manual.html

What It Does The Finmon Ping Service continuously monitors the network connectivity of active alarm units. When a unit goes offline and stops responding, the service automatically raises a Loss of Polling alarm at the control room — just as if the unit had rep...

This page covers the essential programming requirements for all Finmon radio installations. The Finmon GSM Communicator can work with ANY panel that speaks via Dialler with Contact ID. Required Programming Steps The following must be programmed for the Finmon...

This page covers the configuration of direct trigger inputs on the Finmon transmitter. Default Configuration Factory Default Account Code: 9998 When a transmitter is connected to a panel via serial/dialler: The panel will automatically update the radio with ...

Standard Caddx panels connected via Tip & Ring Location Programming Location 0 Segment 1 = 13 (force dial) Segment 2 = 15 (Tone dialling) Segment 3 to 9 = 5555555 (Tel number) Location 1 Segment 1 to 4 = [account code] Location 2 Enter 1 for Contact ID O...

Caddx NX (NX4 & NX8) series panels connected via Tip & Ring Location Programming Location 0 Segment 1 = 13 (force dial) Segment 2 = 15 (Tone dialling) Segment 3 to 9 = 5555555 (Tel number) Location 1 Segment 1 to 4 = [account code] Location 2 Enter 1 for...

Standard DSC PowerSeries prorgramming to get reporting working with Finmon GSM Communicators. Basic Programming Location 301 Enter 5555555 (tel number) LCD Keypad: Backspace and remove 'D', then enter 5's Location 303 Enter 5555555 (backup tel number) Loc...

DSC Neo panels with sub-locations (usually with LCD keypads) Accessing Programming Press *8 Enter Installer Code (default installer code is 5555) Location Programming Location 301 Sub 001: Remove 'D' and enter 555 5555 (Tel number 1) Sub 004: Remove 'E' (...

IDS805 panels with grey serial cable on external serial connector Basic Programming Locations 43 to 46 Enter [Account code] Location 47 Enter 6 (Contact ID) Locations 48 to 54 Enter 5555555 Location 151 Default is 4 dial attempts Enter 0 to disable the...

IDS806 panels with red serial cable Basic Programming Locations 43 to 46 Enter [Account code] Location 47 Enter 6 (Contact ID) Locations 48 to 54 Enter 5555555 Location 196 Must be 000000 Critical for proper operation Installation Procedure Important...

IDS816 panel programming locations Basic Programming Location 111 LED 1 ON All other LEDs OFF Location 116 Enter 5 for Contact ID Location 121 Enter 5555555 Location 128 Sub 2 Enter [Account code] Programming Tips Ensure only LED 1 is on in location...

Complete guide for programming the serial on all X64 variants Serial/App Programming Requirements: Panel firmware: V2.80 or above GSM firmware: V4.51 or above OR E4.19 Draw power from Aux 12V, NOT from serial cable Programming: Loc 40: Ensure value 5 (CID)...

Very old panel - defaults are mostly wrong, use settings below Programming Locations Location 087 Enter 001 for daily test Location 110 Enter 0000 Location 131 LED 1 OFF (report disarm always) Dialer Options Location 135 (Tone dial) LED 3, 4, 5 ON All...

Tested on Plus range version 1.30 Basic Programming Section 810 Select 44 for Contact ID Section 811 Account number for partition 1 Section 812 Account number for partition 2 Section 815 Enter 5555555 Section 817 Enter 5555555 Enabling the Dialer T...

Programming sections for the Evo dialler Basic Dialler Setup Section 3036 Option 3 must be ON to enable the dialler Section 3061-3068 (Account Codes) 3061: Partition 1 account code 3062: Partition 2 account code Section 3070 (Format) Enter 4 x 5 for Cont...

Older Evo model programming Basic Programming Location 521 (Dialer options) LED 3, 4, 5, 6 must be ON All others OFF Location 550 (Format Contact ID) Enter 5555 Location 551 Enter [4-digit account code] Location 561 Enter [Phone number] Important Not...

Configuration for direct trigger inputs using PGM outputs Prerequisites Before starting: Ensure jumper for PGMs is set to positive on panel motherboard If not set: Shut down panel Change jumper position Power up again Important: PGM1 stays negative - onl...

Extended programming guide for MG5050 with dialer module Enable Dialer Section 800 Put numbers 4, 5, 6, 7, 8 OFF (this enables dialer) Basic Configuration Section 810 Enter 44 Section 811 Enter account number for telephone 1 Section 812 Enter account ...